-40%
LAUNCH CR3001 OBD2 Scanner Code Reader Car Engine Scan Fault Diagnostic Tool
$ 12.66
- Description
- Size Guide
Description
Store categorySign Up Now !
You may also like
LAUNCH Automotive OBD2 Diagnostic Scanner Car Check Engine Light OBD Code Reader
Product Description
Launch X431 CR3001 Engine Check including:
1. Reading Codes
Show the detailed description of the Diagnostic Trouble Code (DTCs)
2. Erasing Codes & Reset
Turns off Check Engine Light (MIL), clears codes and resets monitors.
3. Data Stream
Reads and displays live ECU/PCM data stream, plotting functions graphically and stores freeze frame data.
4. I/M Readiness Status
Shows whether the various emissions-related systems on the vehicle are operating properly and are ready for inspection and maintenance testing.
5. Read Live Data Stream
Show the information of continuous data stream from a vehicle in live graphic (waveform) display.
6. View Freeze Frame Data
Check the certain vehicle conditions which are recorded by the on-board computer at the time the emission-related fault occurs.
7. O2 Sensor Test
Allows retrieval and viewing of O2 sensor monitor test results for the most recently performed tests from the vehicle’s on-board computer.
8. On-Board Monitor Test:
Retrieves and displays test results for emission-related powertrain components and systems.
9. Read Vehicle Information
Display the information such as VIN (Vehicle Identification Number), CID (Calibration ID) and CVN (Calibration verification number), etc.
10. Component Test
Certain vehicle components can be actuated by commands sent from the scanner to test their operability
Turn Off ''Check Engine'' Light:
Parts might cause your check engine light on include:
1. Gas Cap
2. Oxygen Sensor
3. Air Fuel Ratio Sensor
4. Mass Air Flow Sensor
5. Ignition Coils
6. Spark Plug Wires
7. Spark Plugs
8. Thermostat
9. EGR Valve
10. Evaporatative Emission Canister Purge Valve(EVAP)
11. Catalytic Converter
If the engine light is not turned off in time, It will Cause Serious environmental pollution , Increased fuel consumption,Increased engine noise.Increased in temperature , ect
Model 6 test of Launch CR3001:
Support Car Models for OBDII diagnostic function:
(Note: CR3001 only Supports 12V Gasoline & Diesel, Does not support 24V Truck )
American Car:
Need Standard OBD2 Protocols from 2000 to now.
for Chrysler , for Ford, for GM, For Jeep ...
European Car :
Need Standard OBD2 Protocols from 2003 to now.
For Alfa romeo , for SAAB ,for Acura , for Opel , for Audi for Seat , for Peugeot , for Renault
For Bentley , for Skoda , for Daewoo , for Benz , for Daihatsu , for Land Rover , for BMW , for Vauxhall , for Citroen , for Volvo , for Fiat , for VW , for Ford , for Jaguar...
Japanese/Korean Car:
Need Standard OBD2 Protocols from 2006 to now.
for KIA, for Isuzu, for Honda , for Mitsubishi, for Hyundai , for Dacia , for Lexus , for Mazda, for Nissan, for Subaru , for Suzuki, for Toyota...
Chinese Car:
Need Standard OBD2 Protocols from 2009 to now
Note: if you are not sure whether CR3001 support your car, please send car brand, model, release year to seller to check it for you
Register and Update:
Please follow the steps below to perform registration and update:
1. Visit the web to enter the product details page.
2. Click “Update Tool” to download it.
3. Unzip and install it on your PC (compatible with Windows XP,
Windows 7, Windows 8 & Windows 10).
4. After the installation is complete, connect one end of the USB cable to the USB port of the PC and the other end to the tool.
5. Once the tool is powered up, launch the update tool on your computer, the system starts reading the tool.
Once it obtains the tool information, it will directly navigate to the update center.
6. Click "Upgrade" to start updating until the update is complete
Specifications:
Screen:1.77 " TFT, 160*128dpi
Voltage Range: 9-18V
Operating Temperature: 0℃ -50 ℃ (32 ℉ -122 ℉ )
Environment Temperature: -20 ℃ -70 ℃ (-4 ℉ -158 ℉ )
Dimension : 118mm*68mm*22.3mm(4.65" *2.68 " *0.88 " )
Weight: <200g
Packing list of Launch CR3001:
1PC * LAUNCH CR3001
1PC * USB Cable
1PC * English manual
FAQ:
System halts when reading data stream. What is the reason?
It may be caused by a slackened connector. Please turn off the tool,firmly connect the connector, and switch it on again.
There is no response when communicating with on-board computer.
Please confirm the proper voltage of power supply and check if the throttle has been closed, the transmission is in the neutral position, and the water is in proper temperature.
Why are there so many fault codes?
Usually, it's caused by poor connection or fault circuit grounding.
Does it support read and clear ABS Airbag error?
No,it only read engine error.
Payment
Shipping
Return
About us
Contact us
Payment
We accept PayPal payment.
Please contact us if you need to use another method to pay.
Payment should be made within 7 days after bidding ends.
Otherwise a Unpaid Item case will be opened to you.
Shipping
Items are generally shipped out within 24 hours after your payment has been cleared (Sat. & Sun. excluded.)
We will arrange the shippment via USPS or FedEx. The delivery time usually takes 2-6 business days( Exclude public holiday), if you need the item urgently, please contact us for detail before purchase.
We are not responsible for wrong or undeliverable address. We reserve the right to charge the shipping fee again for returned items due to wrong address.
Return
We are authorize distributor, our all items are 100% original and Our devices have warranty,
12 months free repair for the devices.
3 months for the accessories.
Please contact us firstly when you need warranty service.
In case an item arrives faulty, please contact us in 30 days and keep it unused.
We will instruct you on how to return and get refund or replacement.
If after 30 days, or the item has been used, we have the right to decline your claim.
About us
We are specialized dealer of On-Board Diagnostic tools and automotive electronics for more than 10 years.
We are authorized first class distributor of Launch, Autel, Thinkcar, Ediag,and Kingbolen brands,and more brands will be show in our store in near future.
You can follow our store and get the news of New Arrival.
Contact us
Business time: GMT8 (9:00-18:00) from Monday to Friday.
Please feel free to contact us via eBay message once you have any question before you giving us negative feedback or open case, we will reply in 24 business hours.
Feedback